Vinyl. Our way of life since 2004 (877) 929-8729

VPI Dealer Authorized & Certified
Site Search
Menu Free shipping on domestic orders over $49.99! - We ship worldwide!
LP20 - 20% Off Vinyl
Home > Products for: '

Vpi Anti Skate

  • 1
Results per page:
  • Anti-Skate Device - JMW-12 Anti-Skate Device - JMW-12 Quick View

    Buy Now

    Anti-Skate Device - JMW-12

    For use with JMW-12

    You will see three rubber rings on the straight shaft; these are used to set the anti-skating force.

    The two rubber rings on the shaft with the grooves are used to set the height of the monofilament. Set the rubber ring on the lowest groove if it is not there already and slip the loop of monofilament over the grooved shaft. Push the second ring down to lock the loop in place on between the first and second groove. Try to keep the monofilament as level as possible but don't go crazy, it is not audible and causes no problem if it is slightly off level.

    You can adjust the settings of the mechanism using the 1/16" Allen wrench provided. Adjust it so the arm can travel to the inner grooves of the record without the mechanism pulling it or causing it to skip grooves.

    Minimal anti-skate force is needed do just enough to keep the image stabilized and the cantilever centered in the groove.

    VPI Accessories
    Anti-Skate Device - JMW-12 Buy Now
  • Armtube For JMW-12.7 Armtube For JMW-12.7 Quick View

    Buy Now

    Armtube For JMW-12.7

    Have more than one cartridge and a JMW 12.7 tonearm? Get an extra armtube and enjoy the benefits of multiple cartridges today! Easy to switch, just remove the old armwand and replace with the new one. That simple! You can switch cartridges in less than 30 seconds! 

    VPI JMW 12.7 Armwand Features: 

    • Nordost Valhalla Internal Wiring 

    VPI JMW 12.7 Armwand Includes: 

    • ArmTube

    • Counterweight 

    • Anti-Skate Ring


    VPI Accessories
    Armtube For JMW-12.7 Buy Now
  • Classic 1 Turntable - Black Classic 1 Turntable - Black Quick View

    Buy Now

    Classic 1 Turntable - Black

    Sterophile Golden Golden

    Absolute Absolute ToneAudio

    Need help choosing the right turntable for you? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.

    **All Cartridges Installed Free Of Charge**

    The VPI Classic 1 turntable comes standard with the unipivot JMW-10.5i tonearm Special Edition in rigid mount mode, new VPI silver coated pure copper wire, a 2.5 thick plinth trimmed with real black oak or real solid walnut finish (at no additional cost), a solid mounted 600 RPM AC synchronous motor, new 2 thick machined aluminum platter, silent inverted bearing, and new isolator feet derived from the HR-X.

    The sound of the Classic 1 turntable is fast, clean, wide open, with deep powerful bass, and unequalled in speed stability. The Classic 1 turntable gives any turntable made regardless of price a serious run for the money.

    This completely new design has produced the simplest and one of the best sounding VPI tables to date.

    VPI Classic Turntable Features:

    Special Edition JMW-10.5i SE tonearm - By giving up vta on the fly adjustments, you get most of the sound of the highly reviewed JMW-10.5i tonearm. A new less expensive base and mounting saves hundreds of dollars but gives up little in sound.

    New 6061 machined aluminum 18 pound high inertia platter with precision inverted bearing and stainless steel damping plate.

    Speed stability on par with a master tape - Due to the rigid mounting of motor - platter - tonearm there is no random motion to cause speed instabilities.

    Noise rejection allowing the Classic 1 turntable to sit on a wood shelf near four 15 subwoofers and having virtually no feedback.

    Lack of random motion between the motor - platter - tonearm gives the ultimate in low level resolution. Not only does this rigidity improve speed stability, it also allows the retrievel of low level information challenging the world's great turntables and master tapes.

    Absolutely solid, non-resonating laminated one-piece chassis holding all components. This is not a wooden frame; it is a solid laminated 2.5 thick MDF block with 11 gauge steel attached to the top with silicone and long bolts through all the layers. The chassis weighs 30 pounds and is totally non-resonant. Now with solid black oak or solid walnut wood finish on all four sides.

    RCA jack termination so you can use the interconnect of your choice.

    Tonearm anti-skate - For those that require the fine adjustment of anti-skate, it is standard on the JMW-10.5i SE.

    Optional lift off full dustcover is available.

    Optional periphery ring clamp.

    Optional SDS power supply.

    Optional XLR conectors.

    VPI Turntables
    Classic 1 - Black
    Buy Now
  • JMW-10 Tonearm JMW-10 Tonearm Quick View

    Buy Now

    JMW-10 Tonearm

    Pivot to spindle distance: 258mm

    Effective length: 273.42mm

    Effective mass: 11g

    Overhang: 15.42mm

    Offset angle: 19.98 degrees

    Average RMS distortion: .311%

    Armtube critically damped internally with 1.7 pound foam.

    Premium Discovery wire used internally and in junction box, optional Nordost Reference wire.

    High quality RCA outputs standard XLR available as an option.

    Unipivot design with zero friction and zero bearing chatter.

    Dropped counterweight for tracking force and azimuth adjustment and low center of gravity.

    Height adjustable base for precise setting of VTA/SRA

    Solid construction of the base assembly guarantees solid bass performance.

    Adjustable anti-skate settings if needed.

    VPI Accessories
    Tonearm Buy Now
  • 1
Go to top