Vinyl. Our way of life since 2004 (877) 929-8729

VPI Dealer Authorized & Certified
Site Search
Menu Free shipping on domestic orders over $49.99! - We ship worldwide!
LP12 - 12% Off Vinyl
Home > Products for: '

Vpi Ads

'
  • 1
Results per page:
  • Analog Drive System (ADS) Analog Drive System (ADS) Quick View

    $1,000.00
    Buy Now
    x

    Analog Drive System (ADS)



    The ADS design includes two pure analog frequency generators featuring low distortion and noise; a high current Class-A/B amplifier that is transformer-coupled to the turntable output; analog control logic for low noise operation; 33/45 RPM analog speed adjustment controls with center detent positions that are factory calibrated for 60/81Hz; analog logic controlled run/stop switching with the output RMS voltage @ 120VAC on startup, followed by a step down to 90VAC after an 8-second delay for quick starting of heavy platters.


    Operational features

    The ADS includes a lighted power on/off switch allowing it to remain powered up during listening sessions for the oscillators to remain warmed up for lowest distortion. There is a separate run/stop switch to control the motor operation. The ADS also utilizes separate 60 Hz and 81 Hz oscillators to eliminate unnecessary switching circuitry in the oscillator circuits for long term speed stability and low oscillator distortion. Turntable speed is chosen using a switch located between the 33 RPM and 45 RPM speed adjustment controls; LEDs indicate the Run/Stop condition and chosen speed. Speed adjustment controls provide a center detent position that is factory calibrated to 60 and 81Hz +/- .02 Hz in their center detented position. The controls also provide fine speed adjustment of approximately 3 Hz through continuously variable linear adjustment controls. The circuitry provides a startup voltage of approximately 120VAC for 8 seconds on startup to assist quick speed ramp of heavier platters, then reduces to 92VAC for its steady state run voltage.


    Speed Control and adjustment

    The front panel contains a two-position push-button switch for selecting either 33 RPM or 45 RPM operation. Pressing the switch either latches it in or releases the switch to its outward position for 33 RPM operation. There are separate speed adjustment controls for 33 and 45 RPM. The controls have a detented center position that is factory calibrated for 60 Hz (33 RPM) and 81 Hz (45 RPM). The speed is also continuously adjustable +/- 3 Hz for fine tuning of the platter speed using a stroboscopic disk and 60 HZ light source. Blue LED indicators adjacent to the controls indicate which speed is set at a glance.


    Motor Stop and Run

    The ADS is meant to be left powered on during the listening session. The platter is started and stopped by the front panel Run/Stop momentary push-button switch. There is an LED indicator the glows red when stopped and green when the platter is turning.


    System power

    There is an IEC power module on the rear panel to supply AC power to the ADS. The IEC module contains a fuse drawer that holds a 1-amp slow blow fuse protecting the ADS from electrical system malfunctions.


    AC power to the ADS is controlled by the power switch located on the left-hand side of the front panel. When the ADS is powered up, the indicator in the switch glows blue indicating the internal power supplies are functioning properly.


    Output to Turntable

    The 125 VAC max output to the motor is supplied by the identified AC receptacle on the rear panel. The receptacle output provides a maximum 20 watts. Higher wattage loads will seriously damage the ADS.


    VPI Accessories
    $1,000.00
    Analog Drive System Buy Now
  • Classic Aluminum Platter And Bearing Classic Aluminum Platter And Bearing Quick View

    $1,000.00
    Buy Now
    x

    Classic Aluminum Platter And Bearing



    Give Your VPI a Facelift and a Performance Boost!  


    VPI owners can now upgrade their older platters to the awesome 2-inch thick Aluminum Platter used on the Classic.  This is a huge upgrade for any VPI turntable and fits every model (except the HR-X).


    Adding the new aluminum/stainless steel platter makes a huge improvement, eliminating noise and improving speed stability.  No ringing, no resonance, just a cool new look and great performance.


    Please let us know which VPI turntable you have, and we will include the correct kit. The platter is identical for all three types, the only difference is the included hardware.



    • The Classic Platter fits most VPI tables without any extra parts or modification

    • Scout Kit includes parts specific to Scout and HW-19 series turntables

    • TNT Kit includes parts specific to all TNT models except HRX (which does not require this upgrade)


    NOTE: Some assembly may be required. 



    VPI Accessories
    $1,000.00
    Classic Platter - Aluminum Buy Now
  • VPI Scout 2 With Classic Signature Arm VPI Scout 2 With Classic Signature Arm Quick View

    $4,200.00
    Buy Now
    x

    VPI Scout 2 With Classic Signature Arm


    Need help choosing the right turntable for you? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    **All Cartridges Installed Free Of Charge**


    The Scout 2 features a 1 7/8 thick aluminum platter (with a stainless steel damping plate) in place of the Scout's 1 3/8 acrylic platter.


    The result of mating a great platter to a simple good looking design! In only seven years, the VPI Scout has become the industry standard as the best-reviewed turntable on the planet! For 2009, we saw fit to bring some big improvements to its best-selling turntable. You may recognize the outboard motor and the plinth, but you will do a double take at the exquisite platter and tonearm.


    Every VPI Scout II comes standard with the JMW 9T! This incredible tonearm features a redesigned armtube that is tapered and filled with a proprietary damping material. This revolutionary design greatly reduces internal resonance, yielding a full and rich sound, with a vast soundstage and increased resolution and detail. The added mass also produces deeper bass response and fantastic compatibility with moving coil cartridges.


    For maximum stability and speed accuracy the platter is made from 1 7/8 thick machined 6061 aluminum and is attached to a nonmagnetic 303 stainless steel damping plate. The entire piece weighs in at an impressive 18 pounds! Because the aluminum is grounded to the steel, there is virtually no static buildup or sonic degradation. What's in the grooves is what comes out of your speakers.


    The VPI Scout II's plinth is made from 1 1/8 thick MDF bonded to a 12 gauge steel plate giving a rigid, non-resonant plinth. The massive platter sits on chrome-hardened ball bearing held by a 60 Rockwell-hardened shaft, below which is a black delrin nut.


    The VPI Scout II generates absolutely no additional noise for a pristinely quiet spin. The AC synchronous motor is contained in a separate steel housing and drives the platter via an Aries belt. This combination produces quiet yet stable running with extremely accurate speed. Speeds are 33 and 45 standard, while 78 is optional.


    VPI Turntables
    $4,200.00
    Scout 2 - Classic Signature Arm Buy Now
  • VPI Avenger Plus Turntable VPI Avenger Plus Turntable Quick View

    $14,999.99
    Buy Now
    x

    VPI Avenger Plus Turntable


    Need help choosing the right turntable for you? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    **All Cartridges Installed Free Of Charge**


    With the creation and introduction of the Avenger and Avenger reference we found there was a large gap between the products in price range. To accommodate those looking for a step up from the Avenger but not ready to take go all in for the Avenger Reference, the Avenger Plus is exactly what it describes. An Avenger "plus" some solid upgrades that make it a step up from the standard Avenger. Using the technically from our behemoth Titan turntable, we have added the Harry Weisfeld Signature Rim Drive motor assembly. With improved engineering to make it easier to use than ever with an adjustable knob to move the rim drive mechanism which is driven by the included Analog Drive System. Additionally the tonearm is getting a step up with the JMW 12-3DR with Nordost Reference wire as well as a periphery ring clamp.


    The VPI Avenger chassis is three layers of bonded acrylic/aluminum/acrylic, with damping material between layers, locked in by 3 isolation steel corner posts, 3 bolts, and the massive bearing assembly. The corner posts which hold the tonearms (up to three will fit) have adjustable machined knobs giving the user the ability to easily raise and lower the height to level the table. Fully adjustable armboards are made from 5/5" 6061 aluminum for rigidity and grounding. The table can mount up to three arms, any manufacture's brand, and any length!


    VPI Turntables
    $14,999.99
    Avenger Plus Turntable
    Buy Now
  • VPI Avenger Reference Turntable VPI Avenger Reference Turntable Quick View

    $20,999.99
    Buy Now
    x

    VPI Avenger Reference Turntable


    Need help choosing the right turntable for you? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    **See Features Tab For Tonearm Upgrade Options - Please Call Our Audio Advisor To Discuss Upgrades**


    **All Cartridges Installed Free Of Charge**


    The VPI Avenger table was originally a project started by Harry over 12 years ago. In the process of the design the project was dropped in mid-production due to excessive demand by HR-X customers which left the design and proto-type chassis to be mothballed. The good news about the abandoned design is Harry instead shifted his focus into starting and completing the VPI Classic Turntable.


    Shortly after the development of the Prime, and while cleaning out the warehouse in preparation for a dealer training event, the forgotten Avenger and its designs were re-discovered! The working name was the Tri-Pod Project. Being newly motivated, Harry has finally put in motion the table that will be his master piece! The unique iterations that had been crafted from the original process were completed as Special Editions.


    This beautiful table comes standard with the Avenger Chassis with Magnetic Drive Platter, JMW 12-3D-R Tonearm, Rim Drive Motor Assembly, Machined Avenger Feet, HR-X Center Weight, ADS and Periphery Ring Clamp.


    This product is not eligible for further discount.


    VPI Turntables
    $20,999.99
    VPI Avenger Reference
    Buy Now
  • VPI Scout 2 Turntable - JMW-9T VPI Scout 2 Turntable - JMW-9T Quick View

    $2,800.00
    Buy Now
    x

    VPI Scout 2 Turntable - JMW-9T




    VPI
    VPI
    VPI
    VPI

    VPI
    VPI
    VPI
    VPI
    VPI

    VPI
    VPI


    Need help choosing the right turntable for you? Please email our audio advisor or call 1-877-929-8729 with any questions or concerns regarding your equipment purchase.


    **All Cartridges Installed Free Of Charge**


    The Scout 2 features a 1 7/8 thick aluminum platter (with a stainless steel damping plate) in place of the Scout's 1 3/8 acrylic platter.


    The result of mating a great platter to a simple good looking design! In only seven years, the VPI Scout has become the industry standard as the best-reviewed turntable on the planet! For 2009, we saw fit to bring some big improvements to its best-selling turntable. You may recognize the outboard motor and the plinth, but you will do a double take at the exquisite platter and tonearm.


    Every VPI Scout II comes standard with the JMW 9T! This incredible tonearm features a redesigned armtube that is tapered and filled with a proprietary damping material. This revolutionary design greatly reduces internal resonance, yielding a full and rich sound, with a vast soundstage and increased resolution and detail. The added mass also produces deeper bass response and fantastic compatibility with moving coil cartridges.


    For maximum stability and speed accuracy the platter is made from 1 7/8 thick machined 6061 aluminum and is attached to a nonmagnetic 303 stainless steel damping plate. The entire piece weighs in at an impressive 18 pounds! Because the aluminum is grounded to the steel, there is virtually no static buildup or sonic degradation. What's in the grooves is what comes out of your speakers.


    The VPI Scout II's plinth is made from 1 1/8 thick MDF bonded to a 12 gauge steel plate giving a rigid, non-resonant plinth. The massive platter sits on chrome-hardened ball bearing held by a 60 Rockwell-hardened shaft, below which is a black delrin nut.


    The VPI Scout II generates absolutely no additional noise for a pristinely quiet spin. The AC synchronous motor is contained in a separate steel housing and drives the platter via an Aries belt. This combination produces quiet yet stable running with extremely accurate speed. Speeds are 33 and 45 standard, while 78 is optional.


    VPI Turntables
    $2,800.00
    Scout 2 - JMW-9T Tonearm
    Buy Now
  • Standard Black Delrin Clamp Standard Black Delrin Clamp Quick View

    $100.00
    Buy Now
    x

    Standard Black Delrin Clamp



    Standard equipment on VPI's Scout series turntables, the Standard Delrin Clamp does an excellent job of reducing the effects of external vibration from interacting with the stylus. This improves focus and pacing, adding weight and power to the sonic presentation.


    Using the Standard Delrin Clamp, can also help reduce (and in some cases eliminate) record warpage and create a much tighter seal between the record and the turntable platter. The clamp essentially locks the record to the platter, reducing vibration typically picked up by the cartridge that colors the sound.


    VPI Accessories
    $100.00
    Delrin Clamp - Standard Black Buy Now
  • 1
Go to top